Видео

Just looking at this man, you know he knows what he's talking about.👍🏼

"You can get a new car battery for about sixty bucks." This is how you know this video is over 10 years old!

I purchased this specifically so I could run a laser printer in my car and every one of them that I own shuts down as soon as I plug them in. Waste of money.

Keep in mind that the batteries he's showing are the highest end ones you can get, and there are perfectly fine AGM and lithium batteries that less than $200 per kwh, they might not be as high a quality, but they will still be perfectly fine and reliable, at least if it's not being used for industrial use where every extra cycle can more than make up for the extra cost.

Thanks

I love how this supposed expert, who is supposedly making a video for people who know even less than he does....has a red battery charger lead going to the black terminal on his battery...without any comment pertaining to it. So.....should people who know nothing just guess whether that means you should have your battery charger's positive wire going to the negative post of your battery and your charger's negative wire going to the positive post? What a basic thing for an expert to leave to chance. Be careful everybody. Anyone can make a video.

Thx

This is the worst "right way" video I've ever seen. To crimp a ring terminal, you absolutely need a special crimping tool. Other methods do not provide a secure and permanent connection. With a properly crimped connection, soldering is no longer necessary. In fact, soldering itself can become a risk if the cables get hot: Solder drips and the connection deteriorates rapidly. This can cause a fire because the resistance increases rapidly.

Why doesn't manufacturers offer this to plug into outlets that offer wire remotes? $49.99

this guy gon get yall car all messed up haha

just bought one used. nothing is burned up inside.. Won't even power on. Any ideas?

Even 10 years later your awesome video Is still helping out! Good explanation. Very well done thank you

What happens if I leave a good deep cycle gel battery on a 15v desulfation cycle for an extended period of time? Thank you in advance.

How to do it the cheap hack way. A good hydraulic crimped off Amazon is $40.

Can you test without load resister or something else that has 100 ohm? Like putting the battery inside of (for example tv remote) and then put the multimeter on both ends while its inside the remote?

Do you still use it? If you dont would you still recommend or recommend something else

If you have a power supply that's DC 14.5 bulbs, and you have an inverter. That's supposed to put out a 110 to a 125 bolts. Why is it that the voltage is reading only a sea voltage on a multimeter? You should be reading a 115 to a 125 V, which does not especially when you have constant current, why is that??

Does the size of your output leads matter I think that larger wires would work better

Looks like you don't have a 2024 comment yet. You are awesome! This video is very interesting and useful! Thanks!

I dont get it, charging and cycling your dead battery is supposed to fix it? Isnt that what everyone does with every dead battery, charge it then cycle it when it wont start your thing.

very informative thanks

4 years ago our Buick had intermittent misfire/no start; local shop charged FORTUNE to replace crank sensor and ignition module. Flash forward today, exact same issues have returned from the grave. Swapped ICM, didn't fix Doing extensive looky loo, have noticed leaking gaskets top and side, the side of block is completely soaked in oil and fluid. Wondering if oils/fluids dripping downwards are shorting out the crank sensor Could that be feasible?

LOL yeah dont do this....

I just put 2 old batteries in series so then it's like 1 decent battery. Sure you need to have more space, but it's way cost effective. Even if my batteries get 1/3 capacity I can just add 3 In series than it's gonna be like having 1 good one

Why r u getting _ 1.4v ???

Best video I've seen yet ,big thank you !

I have a one bad cell lead acid battery 150ah. Maybe destroyed due to low acid+distilled water. I am charging it with my power supply set to 14.4V and 5.2A. Battery currently takes in 12.48V and 5.2A. it's bubbling a lot on all cells apart from the dead one. Should I lower the Amperage and keep it for a long time?

$60 batteries have gone along with the dodo bird.

how long did it last ?

I was interested in the desulfation process. I wanted to look it up because I have a 7-stage charger and was wondering what is the Battery Desulphation mode is. And then, about 09:43 you are openening up some Dragons Milk! Oh wow haha! Nice, I had that before.

In an exposed environment such as under a car's hood, I would crimp and solder. Crimping makes the electrical connection and solder seals the connection from water and dust intrusion. I've seen exposed crimped battery cable connections almost breaking aprart due to corrosion. I've never had a problem with rosin flux corrosion. Acid flux is a different and corrosive flux. That's why today's battery cable clamps are molded around the cable wires as a single unit. The slighest amount of resistance can drop the battery voltage at the starter to the point tha it can't turn over the engine. That can lead to the misdiagnosis as a bad battery.

What are the cranking answers?This red battery that you have here as far as I'm being a commercial battery.What automobile would they have coming from

Why isn't this battery charger's meter accurate?Can you tell me why is it because the spring-loaded?Or is it because they dials?Have a slight high reading or the meter is not quite so good on some battery chargers?

Why isn't this battery charger's meter accurate?Can you tell me why is it because the spring-loaded?Or is it because they dials?Have a slight high reading or the meter is not quite so good on some battery chargers?

Also, if you're preserving it, you will charge it slow.And yes that is the way to do it and second of all run it down again at ten point five volts and chargers again and see if you get the hours on that battery

I still think that the old battery chargers work better.In my opinion but I did find a battery charger that kim put out decent power and put decent hours into the battery

I also just recover to my optima.Solid electrolyte battery lit acid car battery 2 of them that I purchase for $600.I had a couple of quarters.I exchanged them and got them for less than six hundred dollars

But be advised that this battery charger can only go to. Maybe a 45 to a 50 amper hour battery. Most batteries are a little bit more as far as the emperor hour goes. But after we get the battery in service, go out and drive here vehicle to recharge it to full capacity. You should be able to be able to use it again. Like you said before it may not work as when it was new. That's impossible to do, but you still have some good use on that battery.Good luck read my information and comment.Thank you for other helpful information.I thought I would pass some more information to you

And? I just found out there was a battery charger that works certain batteries and will repair a battery. If you have a should say a battery that is a perfect candidate. I suggest you try this battery. Charger on it and tell me whether it did not repair. This factory, this is a noco genius. 2 battery charger you have to put it in force mode. Hold it down for the button down for 3 seconds. The mode button down for 3 seconds in order to get it into force mode.When you see things light up, go ahead and stick it on your battery and leave it there and see if it'll sense that battery and repair.It may take a few hours, but try that anyway.I will talk with you later.I thought I'd laid pass out a helpful hint for you and I have a new type of battery charger

How can you tell if a battery is sulphated if you can't see inside it ??

Sabe alguien de cuanto es su CCA de esas baterías???

I would like to see how you wired the Alternator for Ac current !

This guy went through what can be the arduous process of making his 'how to' vid. I gotta ask, why did he not do the simple thing of spending a couple of dollars and get the 'appropriate' solder he more than once mentions? Whether you are making vids or making cables, it all starts with preparation.

One very important question is do you know JESUS CHRIST AS YOUR PERSONAL LORD AND SAVIOR?

I've seen this done many times. ruclips.net/video/lZEzFP0RwOE/видео.html

Have you ever heard of reverse charging a dead battery? Get the battery to 0 volts then charge it backwards. I heard of this but haven't tried it to see if it actually does anything

Have you ever heard of reverse charging a dead battery? Get the battery to 0 volts then charge it backwards. I heard of this but haven't tried it to see if it actually does anything.

lol when he pointed to the car battery and said this is only about $60! Yep. It was 10 years ago! Probably $160 in 2024!

Hey I have an APC 1200vx from the 80s i want to make a inverter from it can you give me some help?

As a certified Master electrician I approve of this tutorial video. Excellent walkthrough